Floor standing toilet with an electronic bidet seat and the lid raised in a modern bathroom

Will a Bidet Seat Fit Your Toilet? Five Checks Before You Buy

A bidet seat sits on the toilet you already own, so your toilet decides what will fit. Most bidet seat listings show the spray settings, the remote and the heated seat. Few of them mention the pan underneath, and that is where a purchase can go wrong.

Here are five checks you can do with a tape measure and a torch before you spend anything. Pass all five and a bidet seat should be a straightforward swap. Fail one or two and there is usually still a way to get one, it just takes a different route.

Wall hung toilet with an electronic bidet seat and wall flush plate on white hexagon tiles

Check One: Does the Bidet Seat Match Your Bowl Shape?

A bidet seat is made for one bowl shape, so measure your bowl first. Take the old seat off and measure from the centre of the two seat mounting holes to the front edge of the bowl. That is the measurement Toto lists first in its Washlet fitting tips, and Toto is plain about the rule: an elongated bowl needs an elongated seat.

The two shapes are not interchangeable. A longer, oval bowl is elongated. A shorter bowl that looks closer to a circle is round. If you are not sure which you have, write the number down and compare it with the spec sheet for the exact bidet seat you are looking at.

Toto’s tips page is written for the American market, so treat its figures as a guide only. Your own tape measure and the maker’s spec sheet for the model sold here are what count.

Check Two: Bidet Seat Hole Spacing and the Gap to the Cistern

A bidet seat needs its mounting holes in the right place and enough room behind it. Measure the distance between the centres of the two mounting holes, then measure from those holes back to the front of the cistern or the wall. Toto’s fitting tips ask for both, plus a minimum gap between the mounting holes and the cistern. Toto also warns that a cistern with a curved front can stop a Washlet being fitted at all.

What you measure against depends on the toilet you have:

  • Close coupled toilet: the cistern sits on the back of the pan, so measure from the mounting holes to the front face of the cistern.
  • Back to wall toilet: the pan sits flush against the wall, so measure from the mounting holes to the wall or to the cistern above it.
  • Wall hung toilet with an in wall cistern: there is no cistern behind the seat, but the wall and the flush plate are close, and the water and power are hidden behind the wall.

If the holes do not line up with the seat you want, look for a model whose spec sheet matches your pan.

Check Three: Is There a Cold Water Point Near the Toilet?

A bidet seat takes its water from the same supply that fills your cistern. Look behind or beside the toilet for the stop tap that feeds the cistern. Toto’s installation guide shows the setup: a T connector goes at the base of the toilet, the toilet’s supply line runs to one outlet, and the seat’s hose runs to the other.

That connection is plumbing work. The NSW Government’s plumbing, draining and gasfitting licence page says you need a licence or certificate to do any plumbing work, regardless of the cost of the work. So the box can arrive at your door, but the water connection is a job for a licensed plumber.

While you are down there, check the stop tap itself. If it is stiff, weeping or green with corrosion, mention it when you book. It is easier to deal with at the same visit than after the seat is on.

Check Four: Power for a Heated or Electric Bidet Seat

An electric bidet seat needs a power point near the toilet, and not every bathroom has one there. Warm water, a heated seat and a dryer all run on power. Toto’s fitting tips list a powered outlet close to the toilet as one of the fit checks for its electric seats.

If there is no power point within reach, you have two choices:

  • A non-electric seat: Bio Bidet, a bidet seat maker, explains that non-electric seats run on household water pressure alone, with no outlet needed. The water comes out at pipe temperature unless the model has a second line to a hot tap.
  • A new power point: that is electrical work. The NSW Government’s electrical safety in the home page says electrical installation work must be done by a licensed electrician, and that DIY electrical work is dangerous and illegal.

Sort the power question before you order an electric seat. A seat that arrives with nowhere to plug in just sits in its box.

Wall hung toilet with an electronic bidet seat and side control panel on stone look tiles

Check Five: Is the Bidet Seat WaterMark Certified?

A bidet seat connects to your drinking water supply, so check it carries WaterMark certification. The Australian Building Codes Board’s WaterMark Schedule of Products lists bidet douche seats among the products that need certification, and it explains that the Plumbing Code of Australia requires certain plumbing products to be certified and authorised for use in a plumbing installation.

Seats bought online from overseas sellers are the ones to check most carefully. The ABCB’s WaterMark product search lets you look up a product by brand, model or licence number, and the licence number is printed next to the WaterMark symbol on the product. Do the search before you pay, not after the seat arrives.

When a Full Bidet Toilet Makes More Sense Than a Bidet Seat

If your toilet fails one or more of the checks, a new toilet with the bidet built in can be the simpler answer. That usually comes up in three situations:

  • The pan does not fit any seat you like: the bowl shape, hole spacing or cistern gap rules out the models you have looked at.
  • Someone in the house also needs more height: a seat on a low pan is still a low toilet. Have a look at our raised height toilets page if getting on and off is part of the reason for the change.
  • The bathroom is due for work anyway: if the toilet is old or the room is being redone, it makes sense to plan the water and power for a bidet toilet into the bathroom renovation from the start.

Swapping the whole toilet brings its own checks, from the set out of the waste pipe to where the power comes in. We cover those in switching to a smart toilet.

If your toilet passes all five checks, you can order the seat and have it connected by a licensed plumber. Our bidet page explains how Blue Rhino Plumbing connects the seats and smart toilets in homes across Sydney.

Bidet Seat Fit: Common Questions

Will a bidet seat fit any toilet?

No. A bidet seat has to match your bowl shape, line up with the seat mounting holes and have enough room between those holes and the cistern or wall. Toto’s fitting tips also warn that a cistern with a curved front can block a seat. Measure the bowl length, the hole spacing and the gap at the back, then compare the numbers with the spec sheet for the model you want before you buy it.

Do I need a power point for a bidet seat?

Only for an electric seat. Heated water, a warm seat and a dryer all need power, so the seat has to plug into a power point near the toilet. Non-electric seats run on water pressure alone and need no power. If you want an electric seat and there is no power point in reach, a licensed electrician has to add one, because NSW law requires electrical installation work to be done by a licensed electrician.

Can I put a bidet seat on a wall hung toilet?

Often, yes, as long as the pan’s bowl shape and mounting holes suit the seat. The catch with a wall hung toilet is that the water and any power are hidden behind the wall. A plumber needs a water point the seat’s hose can reach, and an electric seat needs a power point close by. Check where both will come from before you order the seat.

How do I check a bidet seat is WaterMark certified?

Look for the WaterMark symbol and the licence number printed beside it on the product or packaging. Then search that number, the brand or the model on the Australian Building Codes Board’s WaterMark product search. Bidet douche seats are on the ABCB’s list of products that need certification. If you are buying online, ask the seller for the licence number and run the search before you pay.

Get a Bidet Seat Connected in Sydney

Done the five checks and still not sure? Have your measurements handy when you get in touch. Blue Rhino Plumbing are licensed plumbers based around Ryde and working across Sydney, and we can tell you whether a bidet seat suits your toilet or a new pan is the better way to go. Contact Blue Rhino Plumbing to book a visit.

Our Services

Blocked Drains and Toilets Gas Fitting Home Water Filter Installation Hot Water Leak Detection Pipe Repairs Plumbing Services Stormwater Drains

For all enquiries call us on 0468 014 771 or simply fill in the enquiry form below.

Contact Form

Get A Free Quote

Speak with our team today to receive a free, no-obligation quote for your plumbing project.

  • Phone: 0468 014 771
  • Email: plumbing@thebluerhino.com
Request A Quote